In order to make a prodded rug, you need the correct tool. A prodding tool has a wooden handle and a pointed end ( that’s not sharp ) made out of metal or wood. Instead of a special tool, you may use a huge knitting needle, anywhere from size 10 to 15. Employ a rug canvas or a burlap base for the rug, then cut it bigger than the size of the finished rug. It should be roughly two inches larger around. In order to cover the raw edges, sew or fold and hem the edges of the burlap.
Heavy woolen fabrics that are used for coats or blankets are normally used for prodded rugs. However, fabrics like denim, acrylic, corduroy, felt or similar types of fabrics might be used. If you use lighter weight fabrics, you should cut the strips twice as wide. An advantage of making a poked rug is that you can use up your bits of fabrics since the strips employed in the rugs are quite little.
If you’re making a prodded rug from a heavy woolen used on burlap, cut the strips three / 4 inches wide and 3 inches long. If you’re using a heavy woolen on rug canvas and heavy cotton fabric, cut the strips 1 inch wide and 3 inches long. For lighter weight fabrics, cut the strips two inches wide and 3 inches long.
To Make the “proddie” ( poked rug ), work from the back side of the rug and, using your poker ( knitting needle ) push each end of the fabric strip thru to the front.
If you’re working on burlap, you’ll need to employ a covering frame or tack the burlap to a wooden frame until almost all of the center is done. The cause of the reason is because burlap is flexible. Use the poker to push a hole into the burlap close to the rug’s center, then take one strip of fabric and push one end through the hole using the poker. Then take the poker and make a 2nd hole just some threads away from the first hole and push the other end of the fabric strip through the second hole. Reach below the rug and pull on the ends to fit them snugly in place . Next, take another strip of fabric and poke one end into the same hole as the last strip. Then move over some threads and poke another and push the other end of the strip thru it. The next fabric strip goes into the same hole as the last one. Do not place the holes so close together that the burlap is distorted. Space the holes about half inch apart. Work in rounds of strips all the way around the center of the rug. Also, do not leave any empty spaces or you’ll need to go back and fill them in later, which would make the procedure much more difficult.
It is straightforward to work proddies on rug canvas because they contain even holes, plus you don’t need to employ a frame because the canvas is already stiff. Work in rows beginning at the center and aiming at the edges. Use the poker to bump one end of the fabric strip thru a hole, then push the other end through the next hole. Tug a little on the ends to make certain the strip is snugly ready. Then push the next strip end thru the next hole and the second end through the next hole, etc . Don’t skip any holes and do not put 2 strips thru the same hole. It is simpler and faster to start with canvas for your first rug.
To care for a prodded rug, do not throw it into the washing machine. To remove the dust, the poked rugs could be shaken, vacuumed with an upholstery tool or beaten with a carpet beater.
If the rug has gotten intensely soiled or stained, you’ll put the rug in a washtub or bath that is brim-full of lukewarm water and liquid fabric soap. ( These are the sole eventualities in which the rug should be washed. ) Squeeze the rug ( don’t wring it ) and work the soapy water through it. Then drain the soapy water and refill the tub with halfhearted water. Rinse the rug by swishing it, then drain the tub and repeat with clean water. Do this till the soap is out. Lay the rug flat to dry on something similar to a piece of screen or sweater drying rack.
you’ll decide that you wish to make your own prodding tool, instead of employing a knitting needle. Buy a wooden egg at a craft store, or use an old darning egg. ( Some of the darning eggs already have handles which will clarify the process as you can just skip to the bit where the end of the dowel is cut and sharpened. )
Drill a hole in the final analysis of the egg that’s enormous enough for a 7 / sixteen or [*FR1″> -inch dowel and about 0.5 in. deep. Fill the hole with wood glue and push the dowel in and seal it. Then wipe off the excess glue. Cut off the dowel about 2 inches from the egg and whittle the end ( you can use a pencil sharpener for a nice point ). Remember that the end should be pointed rather than sharp. Sand the egg and the dowel to make them smooth. Instead of using the dowel, you can use the cut-off end of a knitting needle, if you like. Good deals on carpet runners.
Tags:
carpet runners,
correct tool,
cotton fabric,
knitting needle,
raw edges,
types of fabrics,
woolen fabrics